1. Read the appliance description and the user manual.
2. Prior to ironing, check if the voltage indicated in the appliance data sheet corresponds to the local mains voltage.
3. Do not operate the device if its main cord, plug, indicators or the device itself are obviously damaged, as well as in case the device has been dropped or its water tank leaks. In this case, contact the nearest authorized service center for inspection and repair.
4. Avoid the cord contacting the hot soleplate.
5. Do not touch metal elements of the operated device. Be careful not to burn yourself when using hot steam.
6. Do not allow the cord to hang over the edge of the table or the working surface.
7. To avoid the risk of electric shock never immerse the device into water or other liquids. In case it has happened, do not use the device (see p. 3).
8. Store the appliance and its mains cord in a place unavailable to children.
9. Never leave the appliance unattended when it is connected to the mains or put on the ironing board.
10. The appliance shall be used on an even and stable horizontal surface.
11. Do not use the accessory (-ies) unless recommended by the manufacturer as it may result in injury or the appliance’s damaging, as well as the warranty becoming void.
12. When putting the iron to the heat-insulating platform, make sure that the surface the base is located on is stable.
13. The water emptying cap shall be tightly closed during operation.
14. Do not fill the tank with hot or scented water, flavoring agents, vinegar, starch, descalers, fabric softeners and other chemical agents.
15. Disconnect the appliance from the mains prior to cleaning.
16. Only use the appliance as intended.
17. This device shall not be used by children below 8 and people with reduced physical, sensory or mental capacity, as well as the ones lacking skills and knowledge unless they are supervised or they have been introduced to the instructions on safe operation of the appliance and understand the associated risks.
18. Children shall not operate, clean and/or maintain the appliance unless supervised.
19. Do not use outside.
20. The appliance is only intended for home use.

1. Water filling tank
2. Temperature indicator
3. Soleplate
4. Iron handle
5. Steam output button
6. Temperature regulator
7. Iron retainer
8. Iron
9. Heat-insulating platform
10. Control panel
11. Cord retainer
12. Main base
13. Water tank
14. Water tank handle

Rotate the round handle of the iron to set the soleplate temperature in accordance with the steam mode selected.Make sure that the settings selected match the type of fabric you are going to iron.In case the soleplate temperature mode is selected that is beyond any of the steam modes the appliance can only be used for no-steam ironing.For no-steam ironing just do not press the steam output button.

During ironing, the temperature indicator will go on and off for the iron to support the temperature selected.
Hold on steam output for few seconds as soon as the indicator goes on. This will prevent water drop formation.

1. Power button
2. Steam power mode regulator
3. Power indicator
4. Descaling indicator
5. Filling indicator
6. Low steam power indicator
7. Average steam power indicator
8. High steam power indicator

Power button

Connect the appliance to the mains and press the power button. The power indicator will go on. The default setting is low steam power. The indicator will start flashing. Press and hold the power button for about 2 seconds for the appliance to switch off.

Descaling indicator

If the descaling indicator goes on, it means that the steam generator iron requires scale and mineral deposit removal. To descale the appliance follow the instructions of the Cleaning and Maintenance section. As soon as scale and mineral deposit removal is over, the indicator will go off.

Filling indicator

As soon as the tank does not have enough water for perfect operation, this indicator will go on, and the steam generator iron will emit a single audio alarm and go off. This means water shall be added to the tank. To do this, remove the water tank and fill it with water via a water filling opening. Make sure the water level is between the MIN and MAX marks, then install the water tank in its place.

Filling the detachable tank with water

•     Fill the water tank with water via the water filling opening in it.Make sure the water level is between the MIN and MAX marks at the appliance casing.
•     Heat up the iron to the maximal temperature and then iron a piece of wet fabric to remove any odds from the soleplate.
•     When you switch on the steam generator iron for the first time, it might emit a specific smell. Elements of the device are heating up, and the smell will cease after a while.
•     During the first use, the iron soleplate might emit flakes, particles or dirt. It is okay - the particles are harmless and will cease emitting in a while. Use wet cloth to remove them.
•     During the first use, the steam generator iron might make pumping sounds. This is the sound of water supplied to the steam generator iron and is not a fault.
•     During the heatup process, the soleplate might emit steam, and it is okay. This can continue for 3 seconds, ceasing afterwards.
•     In case the issues described above do not cease after a while, please address an authorized service center for inspection.•To prevent early scaling, please use distilled water.

Dry ironing

•     Put the iron on the heat-insulating platform.
•     Plug the device into the mains and press the power button. The appliance will make a single audio alarm, and the power indicator will go on. The temperature indicator at the soleplate will go on, and the iron will start heating up.
•     Rotate the temperature regulator to select the necessary regime depending on the type of fabric (check Key Advice and Soleplate temperature and steam power modes sections).
•     As soon as the soleplate temperature reaches the selected limit, the temperature indicator will go off, and you will be able to proceed to ironing.

Steam ironing

•     Put the steam generator ironing on a stable and even surface.
•     Remove the water tank and fill it with water via the water filling opening. It is better to use purified water with low calcium concentration. Maximal capacity of the water tank is 1.8 liters. The water level shall remain between the MIN and MAX marks. Put the filled water tank back into the appliance as provided in the user manual.
•     Put the iron on the heat-insulating platform.
•     Plug the device into the mains and press the power button. The appliance will make a single audio alarm, and the power indicator will go on. The temperature indicator at the soleplate will go on, and the iron will start heating up. The default setting is low steam power.
•     Rotate the temperature regulator to select the necessary regime depending on the type of fabric (check Key Advice and Soleplate temperature and steam power modes sections).

At steam ironing, the soleplate temperature mode should match the selected steam power:
•     high steam power - MAX temperature mode;
•     average steam power - 3rd temperature mode;
•     low steam power - the lowest temperature mode for steam ironing.

•     Water in the steam generator iron will heatup, and in a couple of minutes the temperature indicator will go off, indicating that the soleplate temperature has reached the level selected. When the steam output indicator stops flashing and changes to continuous lighting, the iron is ready for ironing.
•     Press the steam output button with a slight effort for steam to emit from the soleplate continuously. Now you can proceed to steam ironing of your clothes.

Cord winding groove

When the device is out of use, the steam hose and the power cord can be wound along the cord winding groove for storage.

Automatic switch off

The device automatically switches off in 10 minutes if no steam is emitted from the soleplate. To restart the device, press the power button again.

Iron platform retainer

Put the iron on the heat-insulating platform and move the iron retainer into position «сlosed lock» to fix the iron on the platform. To remove the iron, move the lock into position «open lock». Now you can remove the iron and proceed to ironing. You can only lift up the steaming station by the handle after you properly fix the iron on the steam generator base (see the picture below)

•     Wipe flakes and any other deposits on the soleplate with a wet cloth or nonabrasive (liquid) detergent.
•     Wipe the upper part of the iron with a soft wet cloth. Use a dry cloth to wipe water remaining on the appliance base and the heat-insulating platform.

You should repeat this procedure at least once a month or after every 10 liters of water used to prevent damaging of the appliance and ensure its perfect performance during operation.

•     Before ironing, always check if the clothes you are going to iron have a label with ironing instructions. Always follow these ironing instructions.
•     The iron heats up faster than it cools down, so it is a good idea to start with ironing of the goods that require the lowest temperature mode, like the ones made of synthetic fiber.
•     If the fabric is made of different fibers, always choose the lowest ironing temperature appropriate.
•     Silk and other fabrics that are likely to become glossy after ironing shall be ironed on the inside.
•     Corduroy and other fabrics that are likely to become glossy shall be ironed in the same direction with a slight effort. Always hold the iron towards the ironing direction.
•     Wool fabrics (100% iron) can be ironed with the steam iron. We recommend setting the temperature regulator to the maximal mode and use a dry cloth as a barrier.
•     Ironing of wool fabrics can make them glossy. This is why you should turn your garments inside out and iron them on the inside.
•     Never iron over zippers sewed into the fabric. This is harmful for the soleplate. Make sure to iron only around such elements.

1. Information on action to be taken if the device is faulty: if you discover any faults with your steam generator iron or unsatisfied with its operation quality, please, address the company you have bought it from. Moreover, for information on technical support offered by Eisenhof you can visit our web-site eisenhof.ru or contact us by email: info@eisenhof.ru
2. The appliance is only intended for home use.
3. Restrictions on using the appliance intended for its operation in residential, commercial and/or industrial premises: the device is only intended for use in residential premises with low to average power consumption in the absence of harmful or hazardous factors. The equipment is intended for operation without permanent attendance by operating staff.
4. At transportation and storage the appliance shall be protected from mechanical damage and other harmful impacts. The device shall be repaired and restored in specialized workshops as set in the warranty certificate. To avoid environmental damage, this device shall be separated from common waste and disposed in the safest way like shipped to a special disposal site.